How to turn engine light off

Drive Your Car and Let the Light Go Off by Itself. Turn Car On and Off Three Times. Some vehicles will automatically reset the trouble codes. Ensure ignition switch is OFF. Cycle ignition switch to ON position and wait minute,.

Reconnect the battery 12v negative cable (black wire). It could be something as simple as its time for a tune up, or something with the emmissions. Check engine light came on for a reason. Press the Erase button on your scanner to clear the error code. Connect the code reader and then turn the key to the on position without starting the engine.

The tool will ask you if you are sure you want to erase the codes, push yes. Using a scan tool is the easiest way for check engine light reset. If you wonder to know how to turn off check engine light by this way, here are steps for you.

Step 1: Connect the scan tool to the OBD – II. Connecting the scan tool to the OBD- II ( On- board diagnostic connector) under your steering column. The check engine light must be turned off after the appropriate repair has been made.

Park the vehicle on a level surface and set the parking brake. The light would be out, and you would be good to go. On very new vehicles, this won’t erase the check engine light at all causing you to think there is still a problem. The safest, and best, way to turn off the light , is with a scanner.

Open this photo in gallery: Photos. Welcome to The Globe and Mail’s comment community.

Step 3: Proceed to the clearing or erasing menu on the scan tool. Follow the prompts on the scan tool’s screen to get to the menu. Upon starting the car, the check engine light should be turned off. If using a scan tool, ensure that it is disconnected from the data link connector before starting the vehicle. Fill Your Cart With Color Today!

The gas cap plays an anti-pollution role. If your cap is loose or missing, hydrocarbons are venting into the atmosphere. In addition to conserving fuel,. Insert the key into the ignition and turn it a quarter turn so the ignition turns on,.

Step on the gas pedal and quickly release it. Do this times in less than seconds. The best way to turn off the check engine light is to fix whatever problem has caused it to come on in the first place.

Fueling the vehicle while it is running can also set check engine light. A good place to start is at your local parts store (ie. NAPA, AutoZone, Advanced). Below are a few things you can do to reset the check engine light. Fix the problem triggering the light If your check engine light came on, the computer detected a problem that needs fixing.

When the check engine light goes on, check under the hood for frayed wires that may need to be fixed right away. A ScanGuage or other OBD-II code reader can reset the check engine light if the issues have been repaired. In some cases, people can reset the check engine light by disconnecting their car battery.

Loose or damaged gas cap: It’s hard to believe that a gas cap can prompt your check engine light to come on, but it can. Your gas cap acts as the seal for your fuel system and it helps maintain the pressure in your fuel tank. A loose or damaged cap can reduce your gas mileage and increase emissions from your car. Get a great smog check and the best smog check coupon.

Using a Trouble Code Scan Tool The easiest and most safe means to turn off the check engine light is by using an OBD II Trouble Code Scan Device. You might purchase a scan tool at your neighborhood car parts store. It can be used to recover stored trouble codes,. Is there a way for me to disable the light ? I need to get the car smogged (live in california) and this light is causing the car to fail. How can I turn off the check engine light.

You can visit a parts stores such as Napa or AutoZone. They will reset your check engine light at no charge. However, be aware that an auto parts salesperson will be performing this procedure. Be wary of recommendations to try this or that part.

After the scan tool confirms the operation is complete, turn the key to the “OFF” position for at least seconds.

You should be able to start the vehicle, at which point the check engine light should be off. Read the manual for your scan tool or app for exact instructions. Allow the engine to idle for minutes, add coolant to the degas bottle as needed to maintain the cold fill MAX mark. Reopen the heater air bleed to release any trapped air and close again.

Maintain engine speed of 0rpm for 3-minutes or until hot air comes from the heater. There is no universally accepted way to safely turn off a check engine light. Even if there was, if the root problem is not addresse it will come back on. Toyota Camry, or Chrysler, they each require individual procedures to diagnose, repair, and reset the check engine light code. The car is, then, driven until the check engine light returns (or, not).

The engine computer is scanne again, and any DTC trouble codes recorded. Clearing the check engine light and readiness tests. After the problem has been correcte the codes are cleared from the memory.

This will cause the MIL to go off , but will also clear the of all tests. Once cleare the PCM will go to work to complete each test and mark them complete.