Brake pad thickness chart

The minimum thickness allowed for a disc brake pad is approximately one millimeter. Because disc brake pads and rotors are vehicle parts that will wear down, it is important to inspect and replace these items when necessary. An acceptable front or rear brake lining thickness is anywhere between the standard millimeter thickness when the break pads are new and millimeter thickness after they become worn.

At millimeters, the sensors get exposed and make contact with the disc or rotor, creating a squealing sound. However, between and millimeters is generally considered the minimum allowed thickness. Pads have about equal amounts of friction material on both pads.

This is caused by proper brake function. To fix this kind of wear, replace the brake pads and hardware such as abutment and anti-rattle clips, service the caliper guide pins and slides. The outboard pad has significantly less friction material than the inboard pad. Hi artcicjunkguy this is lostrider, here is the chart from the Ford Service Manual on the spec for the brake system, hope this helps.

The brake disc’s minimum thickness is not the only factor to pay attention to when inspecting a brake system. Brake pad minimum thickness 3. The tyre tread depth and remaining brake pad thickness must also be checked regularly to ensure that the vehicle achieves its optimum brake reaction. Most brake pads are equipped with sensors built in to the brake pad material. You can inspect the brake pads by lifting your car on a jack and removing the tire.

On most models, you do not need to remove the caliper or unscrew the brake pad mounting pin in order to inspect the thickness of the brake pad. Each brake shoe has only one pad (continuous), as. The thickness requirements are at least 6. Look for worn brake linings.

MOTOR Light Duty Specifications and Quick Reference guides.

At the mechanic to get safety cert. Apparently the rear pads are too thin to pass safety. What is the minimum thickness required? Rear brake disc thickness check. F Illustrates disc brake pads and FI 7. There is no thickness level, manufacturers are different.

As long as there is still even pad left,you are ok. Bendix Catalogue Mobile App. I usually replace brake pads when lining wears down to around 3-mm or the thickness of the backing plate. Getting ready to change my brake pads and would like to know the threshold thickness for replacing the front rotors. All pads have a finite wear life and brake maintenance should also include measuring the pad thickness and checking for sufficient wear material.

First measure the linings to make sure they are each above the minium wear of 0. Next measure the cumulative thickness of the two linings, the pressure plate and the brake disc. As the brake pads wear out completely, the amount of dust on the wheels usually decreases. Noticing cleaner wheels after previous brake dust accumulation may be a sign that brake pads need to be replaced.

On many cars, the brake pad can be seen through the wheel. I took mine off and measure the pads. I just rather be safe then sorry. I drive a suzuki xl-suv.

I use Akebono brand pads at work as those are pretty much a standard OE replacement pad. Or should I wait for the pads to get smaller. Remember, the cheaper the pads , the worse the braking performance and they can also make noise. The brake pads on a commuter’s car, which sees mostly highway driving, might last 50miles, while brake pads on a sports car could last fewer than 20miles. Regular inspection is the true key to determining when you should start thinking about changing brake pads.

Disc brake rotor thickness gauge capable of measuring increments of 0. Thickness must be checked with a micrometer at six or more points around the rotor. I had the front brake pads replaced today at the local dealer. The reason for minimum thickness on brake rotors and pads is because you loose some of your stopping power because of lost heat disipation and also the caliper and piston would be out of its designed travel range. Hello, Anyone knows the thickness of the OEM pads for the front and rear?

Buy online, pick up in-store in minutes. Mm (In.) If the pad lining thickness is equal to or less than the minimum, replace the pad. If necessary, replace the pates.

Check the plates as follows. With other models the brake calipers will have brake pad inspection holes. After you get an idea of how much meat is remaining you can compare this measurement with the thickness of a new brake pad for your model. Also a measurement chart is included in the factory service manual. No need to remove the wheel, just insert the tip into the back of the brake pad through the wheel and see the measument in MM.

As with the excessive wear to the outer brake pad , replacing the caliper and brake pad represents the easiest way to fix this kind of wear. Step 4: Know the signs of tapered pad wear. A third type of wear pattern, tapered wear on a brake pad , is a strong indicator that the brake pad is installed incorrectly.