Replace rear wheel bearing

This is a task that anyone with some automotive experience and garage access can accomplish on their own. Rear wheel bearing location, inspection, removal and replacement. DIY car repair with Scotty Kilmer, an auto mechanic for the last years. How to Change Wheel Bearings. The wheel bearings support the front and rear axle, and all the weight of your car.

Ford Explorer Rear Wheel Bearing Replacement FordTechMakuloco. Unsubscribe from FordTechMakuloco? Rear Wheel Bearings Both sides: As for the rear wheel bearings, they will be a tad cheaper to replace (But this depend on the car type and car model).

The cost of the rear wheel bearing parts will be between $1and $150. The rear wheel bearings on your Subaru vehicle let the tires rotate without much friction. Replacing the rear wheel bearings on your Subaru vehicle is an involved process that requires attention and care.

On your car, the bearing supports the wheel and rides on the axle shaft. It fits into the hollow section at the center of the wheel , and is held in place by the lug bolts which attach the wheel to the car. To replace a wheel bearing , a technician will need put the car on a lift, remove the wheel and tire, and remove the brake caliper and rotor. On some vehicles, the wheel hub and bearing are simply unbolted from the steering knuckle and can replaced as a unit. On a car, a wheel bearing rides on a metal axle shaft and fits tightly inside the hub, which is a hollow chunk of metal at the center of the wheel.

This is often signaled by an audible hum while driving the car. If the rear disc needs to be shaved to less than the minimum, replace the rear disc. If the runout still exceeds the maximum, replace the hub and bearing with a new one.

Disconnect cable from negative battery terminal. Are the rear wheels of your Jeep making too much noise? Sounds like the rear wheel bearings need to be replaced. Luckily, you can use these following instructions to do just that.

Check out this how to replace CCorvette wheel bearings. Track driven CCorvettes or high mileage daily drivers can experience wheel bearing failures. For example, replacing the REAR wheel bearing on a front wheel drive car with disc brakes in the rear is pretty easy, usually, and the labor costs should be pretty affordable.

If it has drum brakes in the rear it will cost more. If, instea you need to replace the front bearing where the drive axle is, both part and labor will likely cost more. After checking the rear wheels, I determined that the passenger side axle bearing was bad and needed to be replaced. Since I was going to go through all the trouble to get the one bearing out, I decided to replace both of them. I ordered Timken Wheel Bearing and Seals, when they arrive I went to work.

A wheel bearing is part of the front and rear wheel hubs. The wheel connects to the hub, and the hub spins smoothly inside the wheel bearing. I have a Expy 4xwith 150miles. Think I can replace my own wheel bearing but wanted a second opion and some guidance on how to approach it. NOTE: If the wheel bearing oil seal is leaking, the rear axle housing vent may be plugged.

Using the special tools, remove the rear axle bearing and wheel bearing oil seal. Lubricate the new rear wheel bearing with rear axle lubricant. Hi All, New member here and proud new owner (a few months ago) of a Ranger. To replace a rear axle seal or bearing , the rear axle should be placed securely on jackstands, and the tire removed. The hub is non-serviceable.

Place a drain pan under the end of the tube to catch any gear oil which may drip. Non-driven wheel bearings - the front- wheel bearings of rear - wheel -drive cars and rear - wheel bearings of front- wheel -drive cars - are similar in design, differing only in detail. The bearing cannot be replaced separately from the hub.

Raise and safely support the vehicle and remove the rear wheels. Replace the hub nut and torque to 1ft-lbs, then stake in place with a hammer and punch. This rear wheel bearing how-to is nearly the exact procedure you would. At times, worn or pitted rollers, chipped or damaged bearings can wear a groove into the axle shaft. How do mechanics replace wheel bearings?

The complexity of wheel bearing replacement varies greatly depending on the vehicle make, model, year, wheel position (front vs. rear ), and drive type (AWD vs. FWD). If your CV joints need attention, or your rubber boot is ripped or damage then now would be the ideal time to replace it. Remove the brake caliper and rotor. On my 9rear wheel bearing , do I need.

On vehicles with all- wheel drive, remove the wheel drive shaft spindle nut. Important: Do not damage the wheel drive shaft joint seal. If the ABS light stays on, the steering feels loose, your car vibrates, or you hear noises when driving at high speeds, it is time to replace your wheel hub.

Fixing the bearing is important and if not repaire your wheel may begin to separate from the vehicle or create issues when steering. How To Replace A Wheel Bearing On A Freelander If you have a bad rumbling droning noise coming from (in our case) the rear of the Freelander chances are it will be a wheel bearing (s). This post shows you how we replaced the wheel bearings. I had to replace because the rear end was grabbing and pulling to one side.

That thing was noisy, sounded like the when the u joints used to go out. Did the work myself in my driveway, not to hard to do.

I did have a shop press the bearing for me. The old bearing was in pieces when the shop guy gave it to me. Installing Wheel Bearing Assembly. To remove the hub you will destroy your old bearings.

When I let the dealer replace my right rear bearing and hub I was shocked when the bill went over $500. It is nearly unheard of for a wheel bearing to fail totally, without warning.

That being the case, Leave it and keep your ears open. It will tell you once it needs replacing, and you will have time to get to it. As a general rule, the old type bearings (the ones that are $ea. to replace ) are always done in pairs.