Pressure plate torque specs

Torque specs , pressure plate to flywheel. I was in class today and we finally got the transmission dropped on my buddies car. I tried downloading the manual but it freezes my computer. Gotta be careful about the misprints though.

Next, you need to install your dowel pins that came with the clutch kit, or with your ford racing metric dowel and pressure plate bolt kit. These will gently hammer into none threaded holes, these holes are also tapered so they will only go in half way. Also, on the new clutch assembly there are two small blocks of wood wedged between the pressure plate and the throwout bearing. As far as I know, the bolts are re-usable.

Though, when I installed my Fidanza flywheel, it came with new bolts for the pressure plate ,. What are the torque specs. The Ford manual put the final torque for the flywheel in a different place in the torque chart from the stage torques. And is it good enough for the pressure plate ? Cam thrust plate bolts 8-ft-lbs. Well luckily I put the flywheel to lbs as I found that while searching the net.

I ended up torquing the pressure plate to lbs. Main bearing torque sequence -4. Engine Mechanical Components. Flywheel - to Foot Pounds 2. Pressure Plate - to Foot Pounds 3. Bell Housing - No specs found. SOURCE: Bolt torque specs for flywheel, pressure plate , 1. I have searched on here and have had a number of different torque specs listed as actual specs.

Does anybody have this information handy? Sponsored Links Remove Advertisements. Oil pan to front cover lb. I lost my old IT Book and got a new one. I looked and find differing opinions.

When i install my clutch today, what are the torque specs on the pressure plate are there any? This is TOO MUCH torque for the original style seals. This spec is not found in Willys manuals. Special thanks to crackeregg for making these documents available in a digital format (saved me a lot of typing!).

Anyone know the torque specs on the KA pressure plate bolts. I needed the torque valve for the bolts on the pressure plate and the flywheel. Is that what your looking for?

Yea I saw the torque value for the bolts but I though maybe you were looking for the torque rating of the clutch as well. MG Midget and Sprite Technical Are there torque specs for the pressure plate? Make sure you clean the threads in the crank flange and use some thread sealant.

Most will use blue loctite. Be very careful about the bolt lengths. Then torque the six (6) pressure plate nuts to lbs.

When you are sure the clutch is mounted properly, it is time to re-install your transmission. Use a transmission jack and carefully slide the transmission input shaft into the clutch and slide the splines through the clutch disk. I pulled these numbers right off of All Data. I do but most everyone else here are close enough. The main thing as per McLeod was to use the impact gun or air gun at lowest setting until the fingers of the pressure plate stop moving and the crush washer collapse then torque to spec.

Since I didnt buy the kit myself I do not have the torque specs or the allignment tool. My interweb kung foo is no good today. Coyote torque specs FF Tech. Once those bolts are remove lift the shifter and spring out of the housing and set aside.

Below is another snip from the FSM outlining these steps. Fastener Specifications (LS). The user assumes all responsibility for the use of this material. TIGHTENING TORQUE The following charts are for reference only. It is the responsibility of the user to verify the accuracy of this material before use.

These torque specs come in handy if you are changing differential flui rebuilding the axle, or regearing. These specs only apply for the front Dana axle for TJ Wranglers. Dana front axles came standard on Rubicon models, it was not available for any other models.

TORQUE REMOVE CONNECTING ROD BEARING CAP NUTS. Seat each camshaft by pushing it towards the dizzy side of cylinder head. The torque specs for the pressure plate should be torqued to ft. I need this asap if someone could provide it for me.

The manual transmission flywheel bolt torque specs and the pressure plate bolt torque specs. In order to be able to post messages on the Forums at Modded Mustangs forums, you must first register. I am 1 sure that your numbers are accurate according to what you are reading.

Any help would be greatly appreciated. TBI stands for Throttle Body Injection, MPI stands for Multi-Point Injection. Your Wrangler with either have a Carburetor, TBI, or MPI for its fuel delivery.