How to change a pool light

Assuming you mean the light, first make sure the circuit is off. Remove the old light by removing the single retaining screw that holds it to the wall. Just like there are two types of in ground pool (vinyl liner and concrete) there are two basic types of light that go in them. And it is usually fairly easy. Look closely at the metal ring which encases the glass.

You will see a screw hea usually at the top. Unfasten this one screw and the entire housing can be pulled out of the niche. To change a pool light , start by shutting off all power to the pool.

Remove the screw at the top of the lighting fixture and use a flat-head screwdriver to pry the fixture out of the niche box. Next, unscrew or pry the lens off the fixture and replace the old bulb with a new one. There is not one standard replacement bulb and gasket for all pool lights.

If you already know the make and model of your pool light , go to our Light Parts page to find the proper bulb and gasket. Set up the new light bulb and gasket and change the pool lens on the housing. Submerge the housing in the water to check whether there are any air leaks. Tighten the screw or screws holding the bezel to the pool light housing.

Wind the housing cord around the housing. Insert the housing into the pool light opening in the pool wall. If a steady stream of air bubbles escapes from the housing after you submerge it in the water, you must remove and replace the bezel,. Make sure the screw hole (s) in the fixture line up with the one(s) in the wall, then replace the screw(s).

How to install a pool light. Align the supply wire (black) with the black wire from your lighting unit, and the neutral supply wire (white) to the white wire from the light. Put the cover back on the junction box, or simply close it. Test that everything is working by turning the electrical breaker on. You may have to get back in the water to return the cord to its previous position behind the niche in the pool.

Once the cord is in place, push the light fixture back against the wall or into the niche. A swimming pool light isn’t necessary but adds to the aesthetics of your pool at night. Step 6: Return Light to Pool.

Wrap the light’s power cord around the back of the housing (or as you found it originally) so that it fits back into the niche easily. Return the light housing to the niche or casing in the pool wall, and secure it to the wall with the screw that was removed in step 3. Steps to change pool light in swimming pool. Screw the bulb in the housing socket of the pool light so that it can easily get fixed. For the halogen bulbs, one needs to first push the bulb inside and then twist it a little bit to bring it out with better quality. Installing the new light bulbs.

Money well spent, if you ask me! Lowering the thermostat a few degrees during periods of non-use also reduces the cost to run a pool heater. In order to replace an inground swimming pool light fixture, you have to pull the light all the way out from the junction box and thread the new cord all the way back through. Go to the junction box and unplug the light fixture from its socket.

Attach a long piece of string onto it. Turn off the circuit breaker in case you have the wrong light. Changing A Jandy Swimming Pool Light Bulb.

The top center screw hole on the outer steel face ring needs to line up with the top position of the fixture marked by the sticker around the outside. Now the plastic clamp assembly needs to be lined up with the back of the fixture with the clamp opening at the top and held in position with the original screws. Turn the breaker back on to the pool light , and reset the GFCI switch to on.

Flip the light switch on and then off quickly to ensure that the light is working properly. Do not leave the light on for more than a few seconds as this can cause the light to overheat when it is not submerged in water. I pulled my pool light out, thinking I only needed to replace the bulb. Once I inspected it, I noticed that the black coating in the base of it where the bulb gets screwed in has bubbled and burst.

Maybe your pool light just broke or maybe you want to spruce up your swimming pool and replace that broken halogen light with a brand new LED pool light. Either way, before you get started there’s a few things you probably want to know first. This four (4) feet of cord coiled around the light allows the light to be serviced after the pool is filled with water. Cut the cord at the Junction Box, leaving at least size (6) inches of cord to make connections. We offer the best selection of pool and spa chemicals, pool cleaners, pool equipment, cleaning accessories and pool inflatables and floats.

We have the solution to all your pool and spa needs. Every store also offers Free In-Store Water Testing and Free In-Store labor on repairs. Brand of Light – there are many brands of pool lights on the market.

Some cheap ones can be found on eBay.

The halogens start at $1and the LED’s start at $150. For deep fixture lights, you can wrap the cord around the fixture. There is a notch on the bottom of the fixture that catches on the bottom of the niche.

Now, screw in the pilot screw or snap in the clipable type. If you who had to disconnect the cord at the junction box,. Pool light bulb replacement technicians are difficult to find because even the best techs can’t guarantee that the light wont leak. With every one out of five fixtures leaking, the call-back percentage is just too high so pool tech’s refuse to replace a pool light bulb. What the pool guy will replace is the entire fixture.

To make sure, find the pool’s electrical breaker near the equipment pad and set your multimeter to AC voltage. Put one of the meter contacts on the neutral post and another on the hot side (or the source side and switch side). If the switch for the light is working fine,. Check the light wiring connection to the junction box at the pool side and to the AC power switch.

Be sure that there is proper AC power applied to the light. The only required maintenance for any pool light is bulb replacement. Regardless of the type of light , you should never have to lower the water level in the pool to replace the bulb. In some cases, you can loosen a single screw, elevate the bulb housing above water level and replace the bulb. Pool professionals fear that replacing a 120V light for a 12V light will take hours of electrical work.

Due to advancements in technology, this is no longer the case. If a pool light already has a junction box, there are UL-listed retrofit kits that are able to switch most mainstream pool lighting from 120V to 12V in just minutes. Use quality tools of proper size, so as not to strip any of the soft metal screws, bolts, etc. On very old fixtures, screws may break easily, or be corroded from years of water and chemical exposure.

Old model lights have brass screws around the fixture, which tighten down on tabs. Hanging over the pool , coil the light cable around the light fixture as you lower the light toward the niche. Once you have the light in the niche, set the bottom tab of the light into the slot on the bottom of the light ring to hold the light steady.

Using a screwdriver, take the light screw and install the one screw in the top of the light. Replacement Pool and Spa Bulbs.