How to change pool light

Shut off power at the breaker, and also at any other switches. It is not necessary to lower the water level. Most all light fixtures have enough cord coiled up inside of the light niche to allow the fixture to be brought up onto the coping stone for repair.

Remove the single stainless steel screw at the top of the light. Replace all screws and lock in all tabs to close the light fixture. Place the fixture back into light niche and screw in the top screw. Turn the power back on by switching the. Caution: Possible Electrical Shock or Electrocution: For your safety please use.

You will first need to purchase the correct replacement pool light bulb. Set up the new light bulb and gasket and change the pool lens on the housing. Submerge the housing in the water to check whether there are any air leaks. Look for the single screw along the bottom of the pool light housing bezel.

Remove and discard any corroded screws and replace them with new ones obtained at your pool supply. Align the supply wire (black) with the black wire from your lighting unit, and the neutral supply wire (white) to the white wire from the light. Put the cover back on the junction box, or simply close it. Test that everything is working by turning the electrical breaker on. You may have to get back in the water to return the cord to its previous position behind the niche in the pool.

Once the cord is in place, push the light fixture back against the wall or into the niche. Replace the screw at the top of the light to hold it in place. Install the new light bulb and gasket and replace the pool lens on the housing. Tighten the clamp screw or replace the screws you removed previously to secure the lens.

Submerse the housing underwater to check for air leaks. You may see one or two air bubbles, which is normal, but a steady stream of bubbles would mean. PULL LIGHT CABLE OUT OF WALL - Pull the light cord out of the pool wall. There is a conduit between the pool and the J-Box at the house.

When you pull out the light cable at the pool , you will be pulling the cable out of the conduit and pulling through the cord that you attached to the other end. Check Out Changing Color Pool Light on eBay. Fill Your Cart With Color Today! Before you get going, it’s best to gather everything you need. To begin, locate the circuit panel for your pool,.

Step 2: Turn Off Electricity. Most pool lights have a single Phillips-head. A lot of LED bulbs also have the ability to change colors, adding more fun to your evening pool parties and nighttime swims. If you click this link and make a purchase, we earn a commission at no additional cost to you. Make sure the screw holes line up properly, then replace the screws.

Now that the bulb has been replace you can turn on the electricity to your pool and begin enjoying your well-lit pool again. Every pool owner knows that after the cost to buy a pool heater, there is the cost to install a pool heater, and then the cost to run a pool heater. Solar heat is Free, but not so reliable or dependable.

In order to replace an inground swimming pool light fixture, you have to pull the light all the way out from the junction box and thread the new cord all the way back through. Go to the junction box and unplug the light fixture from its socket. Attach a long piece of string onto it. Turn off the circuit breaker in case you have the wrong light.

When you go to replace a pool light bulb , keep in mind that working with water and electricity requires special attention to safety. Changing A Jandy Swimming Pool Light Bulb This is a write up covering how we changed the light bulb on a Jandy pool light (Jandy part number WPHV500WS10 also known as Jandy Pro Series Large White Light ) and a Jandy White small light. This four (4) feet of cord coiled around the light allows the light to be serviced after the pool is filled with water.

Cut the cord at the Junction Box, leaving at least size (6) inches of cord to make connections. No need to drain the pool. There is usually a single screw holding the light in the niche. Then hopefully there is enough cord to pull the light up on the deck so you can change the bulb.

I pulled my pool light out, thinking I only needed to replace the bulb. Once I inspected it, I noticed that the black coating in the base of it where the bulb gets screwed in has bubbled and burst. It is a good idea to put a piece of tape over the breaker. Now, to get the light fixture out, you will need to unscrew the small pilot screw that holds the fixture in. And being the stand-up company that we are, we would replace the entire pool light fixture at no additional cost to the customer and lose money while doing so.

A new pool light gasket for the fixture is about $25. Profit on a successful job would be about $120. Check the light wiring connection to the junction box at the pool side and to the AC power switch. Hanging over the pool , coil the light cable around the light fixture as you lower the light toward the niche. Be sure that there is proper AC power applied to the light.

Once you have the light in the niche, set the bottom tab of the light into the slot on the bottom of the light ring to hold the light steady. Using a screwdriver, take the light screw and install the one screw in the top of the light. The only required maintenance for any pool light is bulb replacement. Regardless of the type of light , you should never have to lower the water level in the pool to replace the bulb.

In some cases, you can loosen a single screw, elevate the bulb housing above water level and replace the bulb. Flip the light switch on and then off quickly to ensure that the light is working properly. Do not leave the light on for more than a few seconds as this can cause the light to overheat when it is not submerged in water.

Test the light to insure that it is working properly. Mount the light on the pool wall according to manufacturer specifications. If you have a hard wall pool and are using a corded light , remove the edging over the area where you are going to install the light.

Run the cord over the pool edge and then replace the edging. While some products simply change the color to blue or re others offer colorful light shows using an array of different colors. Choose a color to make those late night pool parties more festive, induce romance while poolside with that special someone or experience tranquility during a late night swim. Use quality tools of proper size, so as not to strip any of the soft metal screws, bolts, etc.

On very old fixtures, screws may break easily, or be corroded from years of water and chemical exposure.

Old model lights have brass screws around the fixture, which tighten down on tabs.