How to remove a flywheel

I assume you have the transmission removed. Once you take off the bolts holding the torque converter you remove it and in the center of the flex plate there are four bolts that have to be removed and the flex plate can be removed. Simply, first off WDdoes not loosen anything that is not rusted.

Secondly I can tell you how to get the nut off but unless you have a pulley puller you are screwed. They are on a tapered shaft. It has to come off evenly and only a. Remove the flywheel nut holding the flywheel to the crankshaft.

The easiest way to do this is with a impact wrench and socket, but if that is not available, than a strap wrench can be used to hold. The flywheel is attached to the back of the crankshaft. When the starter motor is engage a gear within the starter meshes with these teeth to turn the engine.

If the teeth on the flywheel have worn down, the starter will not be able to turn the flywheel and the engine will not start. Before replacing the flywheel you must remove the manual transmission and clutch assemblies.

Once this is complete the flywheel is expose start by using an air impact gun to remove the flywheel mounting bolts. At this point the flywheel may become loose so keep your hands on it. There are several techniques that may be employed to accomplish removal. You can remove the flywheel from a mercury outboard motor by keeping the flywheel stationary and using a special tool called a flywheel puller. Unlatch the clips that are used to secure the cover and take the cover off the motor.

To remove the flywheel there are a few steps in the procedure to properly remove it and not ruin things. As you will usually be working on an older motor where replacing broken parts may be expensive IF you can even find the parts. Bend down the lock tab on the flywheel bolt using the wood chisel, Tommy bar and hammer.

Pull start housing usually about bolts 4. Magnetic housing from around the fly wheel 5. Use a gear puller, one used for cars. Flywheel nut from on top the fly wheel 6. Usually the Harmonic balance puller works best 7. If the cover is secured by rubber grommets, lift the cover at one or both ends to pull the cover off the grommets. If the plastic flywheel cover does not coming off easily, check closely for any fasteners. Then, remove the bolts holding the shroud in place and remove the shroud.

If the engine is equipped with a flywheel brake, remove any cover and disconnect the outer end of the brake spring. If your engine is equipped with a flywheel clutch, remove it while holding the flywheel with a flywheel holder or a flywheel strap wrench. To reveal the flywheel , pull the transmission towards the back of the car, once it has been disconnected.

This is the smartest way to remove the engine flywheel.

Disconnect the spark plug wire and remove the spark plug. Insert nylon rope into the spark plug hole to jam the piston and keep the crankshaft from turning while you remove the flywheel bolt. Internal Right hand female. And make sure you follow your servi. After freeing the flywheel , loosen the top nuts on the flywheel puller shafts.

Unthread the flywheel puller shafts from the top of the flywheel and remove the flywheel puller tool. Grasp the flywheel and raise the entire engine assembly slightly above the work surface. Continue holding the flywheel securely with one han while striking the end of the crankshaft with a rubber mallet. Repeat this step until the flywheel disengages the crankshaft and engine.

How to remove the flywheel. Rules, New Member Introductions, and Forum Information. If the replacement motor does not include a flywheel , remove the flywheel from the old motor and place it on the new motor. Hold the motor axle on the end of the motor opposite the flywheel with a pair of vice grips and twist the flywheel off. Before using this site please read the site disclaimer.

The first part of this is done on a CDI engine and the second half of the photos are from a TI engine, for those who are curious about the change in photos. Briggs and Stratton flywheel removal. Around here, the expert usually.

Clean the flywheel carefully to remove any residual adhesive or debris. Loosen pressure plate bolts (1-8) evenly, a few threads at a time and in a diagonal pattern to prevent warping the plate. To get the flywheel off, first remove the small bolt holding it on then use a flywheel puller. Re: how to remove flywheel ? Loosen the large flywheel retaining nut in the center of the flywheel about turns.

In order for an engine to start, a spark is necessary. The rotation of the flywheel brings this spark at the precise. Important: The engine flywheel housing has dowels that protrude into the upper oil pan and the engine block.

Make sure it is supported before you remove the bolts that hold it. Place it down and you will see the pressure plate covering the flywheel. Step 10: Install the new pilot with the bearings that came into the kit. Don`t cut your hands on the ring gear, wear gloves.

The puller for the 7flywheel is a bolt. It fits in the hole that the bolt,that holds the flywheel ,threads out of. It threads into the flywheel hub and pulls it off of the crank. Place the flywheel strap wrench around the entire flywheel. Tighten the flywheel strap wrench by winding it clockwise to take out any slack.

Turn the breaker bar counterclockwise to remove the nut. If flywheel is struck on use a puller. Stihl uses a knocker type puller that screw on the crankshaft and tapped by a hammer.